AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Single pin stack12/11/2023 ![]() You must buy the jig and frame separately in our 3D Gun Builder store. This rule may seem arbitrary, but it does make it a PITA for 80% of builders and distributors to enjoy the 80% building hobby. Recent laws have made shipping both Polymer 80 jigs and frames illegal. If you are familiar with the Glock models, this frame is the single stack magazine version which is relatively slimmer than the average Glock. The part number for the PF94SS jig is P80-PG94SS-JIG.įor the Single Stack version of the Polymer 80, you will need to drill the M3, and M4 labeled pin holes. ![]() The PF94SS or the Glock 43 Polymer 80 jig is the single stack red jig with the tab removal template, locking block area, and drill bits for the pin holes. The G26 or sub-compact p80 does not require the third locking block pin or pinhole. The part number for the PF940SC jig is P80-PG940SC-JIG.įor the Sub Compact version of the Polymer 80, you will need to drill only the M4 labeled pin holes. The PF940SC or the Glock 26 Polymer 80 jig is the smaller sub-compact red jig with the tab removal template, locking block area, and drill bits for the pin holes. This is overall the same as the compact G19 build but slightly larger. The part number for the PF940v2 jig is P80-PG940v2-JIG.įor the full-size version of the Polymer 80, you will need to drill the M3, and M4 labeled pin holes. The PF940v2 or the Glock 17 Polymer 80 jig is the standard full-size red jig with the tab removal template, locking block area, and drill bits for the pin holes. The part number for the PF940C jig is P80-PG940C-JIG.įor the Compact version of the Polymer 80, you will need to drill the M3, and M4 labeled pin holes. For the Single Stack version of the Polymer 80, you will need to drill the M3, and M4 labeled pin holes. The PF940C or the Glock 19 Polymer 80 jig only is the standard red jig with the tab removal template, locking block area, and drill bits for the pin holes. Let’s dive into the differences in the jigs between the various Polymer 80 versions. The placement of the pin holes varies between models, but the tab removal process is always the same. The differences are mainly in the overall frame size template for the jig or altered pinhole placement. The Polymer 80 jigs are similar to the method used to complete your build. While it may seem counterintuitive, it is suggested by the manufacturer and just works. Use a hand drill only for the Polymer 80 jig.Do not use a drill press the bit can sometimes be just slightly unaligned and will lead to an unusable frame.Before drilling, place the jig on a flat, even, hard surface.Ensure your frame is seated and locked fully within the Polymer 80 jig.A new type Pinner has been added to the runtime package. Take your time and build your P80 frame properly the first time around.Ī few tips for drilling holes correctly to keep in mind: GODEBUGcgocheck1 is still available (and is still the default). You can finish with a bit of wet 2000 grit sandpaper to make your Polymer 80 frame look factory-finished.ĭrilling the holes for the Polymer 80 sounds like a “no brainer” task.Continue raising the grit of the sandpaper after removing the jig until you are over 1500 grit and the tab removal area is smooth.Sand down with 60 or 80-grit sandpaper.Purchase “flat” end snips and cut the tabs down as close to flush with the frame and jig as possible.Having built a handful of Polymer 80s myself, I have found that there is a trick to make removing the P80 tabs easy: While you can’t go full out with a Dremel to finish the frame ( you will remove too much polymer once close to the jig), you can start with the Dremel tool. The rail guides or tab cutouts show Polymer 80 builders which part of the polymer frame to remove to install the rear rails and locking block. With silent, click-free yardage adjustments, a sleek and trim frame, and both single and Double Pin options, the FAST EDDIE is sure to satisfy the needs of today’s hardcore hunter.Building 80% firearms require patience and studying but can be accomplished by nearly anyone with a brain. ![]() Spot Hoog Fast Eddie Single Pin MRT Sight is light, quiet, and easy to use the FAST EDDIE was designed with the hunter in mind.
0 Comments
Read More
Leave a Reply. |